How to Install the Quick-Release Push-Button Lock for Your Window Guard

Attach typically the Strike Pin for your window guard

The Strike Pin (3) should be forever mounted on or close to the outer metal framing of the window guard -referred to be able to from now in as WG- on the side of the WG’s “door” opposite associated with the hinge, around the middle (the same place where a doorknob is located on a door). This should extend facing outward from the WOHNGEMEINSCHAFT toward the walls, so that this will later go into the Secure Box tip-first whenever closed.

IMPORTANT: Typically the Strike Pin need to point straight as is possible, ie not directed slightly up, along, to the remaining, or to the best. The straighter it is, the smoother their operation later.

The back of the Reach Pin has threads to get a 1/4″ sl?, so a common way of attaching the strike green to your WOHNGRUPPE through first fixing a 1/4″ bolt it, then screwing the Strike Flag into that. Even so, you cannot want folks having the capacity to simply unscrew the bolt from the outside, so it is important that an individual permanently correct it in order to the WG. This is certainly most often performed by spot welded the attached Reach Pin in place, yet if a welder isn’t handy, any way the bolt may be made unturnable works, such as working with one-way bolts.

Mount the Window Protect

If this isn’t currently, it’s time in order to mount the WG on your windows. Attach the Secure Box (1) for the end of your pin so of which it locks in position. If it is just not, be sure it is usually unlocked first simply by pushing the conclusion regarding the Push Fishing rod (2) into the particular smaller hole regarding the Lock Field first. This Lock Box will be attached to the outside wall of your current building, so that you will need to install typically the WG in a new position the location where the Locking mechanism Box may be installed using the leading and bottom mess holes, and should not be pryed off (such as when it sits off the particular edge of the window frame).

The other issue to keep inside mind this is that will there will be an approximately 1/2″ hole drilled via your wall situated in the midst of the Lock Box, and on the inside of the building, a a single 5/8″ diameter Flange will mount to the wall about that hole. When you put upwards the WG, an individual want the Freeze Box to always be near to the window starting, but far good enough enabling this 1/2″ hole to end up being drilled throughout the wall membrane, and hopefully turn out to be clear of virtually any inner wall obstructions (like inside framing) for a a single 5/8″ diameter all-around the hole centre.

Mark your gap

With the Reach Pin attached in order to your WG, in addition to the WG attached to your constructing, the rest is relatively very simple!

Now we require to mark where hole will become drilled through typically the wall in order that it fits the small pit on the again of the Lock Box. First, push the Push Fly fishing rod (2) in to the Lock Box hole as a result it releases in the Strike Pin, in addition to remove it. Spot the Cardboard Fall (4) completely onto the Strike Pin, and shut down the particular end with a knife so the cardboard only barely extends beyond the Strike Pin. push button box Shut the WG doorway slowly until the round of cardboard satisfies the wall, next use a pen to draw some sort of circle where it lands.

Drill

Technically a 3/8″ drill down bit will get big enough for the particular Push Rod in order to fit into, nevertheless I recommend a new 1/2″ bit, which in turn leaves more room for error, in addition to is covered upwards just fine. Using the circle you only marked, drill some sort of hole straight by means of your building wall membrane until you breach lack of.

At this particular point, reattach typically the Lock Box for the WG and keep it closed. A person from the inside should be capable to put their own eye throughout the recently drilled hole plus see the OVERALL small hole involving the Lock Field. If it is definitely partially covered, exercise your hole until which clear route to it.

Attach the Lock Package

If it is not already, reattach the particular Lock Box towards the WG and keep it closed. Mark the upper in addition to lower holes of the Lock Container with your trusty pencil, then open the WG plus drill them together with the drill little bit (NOT the huge one! ) that will matches the screws you’re going in order to use to install the Lock Container, which don’t include the kit. These kinds of screws should become between 1/4″ and 3/8″, and need to be about 2″ to 3″ lengthy.

With your a couple of holes drilled previously mentioned and below your own BIG one, take away the Lock Box from your WG (you learn how by now, appropriate? ), place that on the wall structure, and mount that with your screws. Screw them throughout until they’re cuddle, smaller completely tighten up as of this time.

Align the particular Lock Box

Slowly close the WG towards your mounted Lock Box, being mindful To never lock it in place. What’s that? You say typically the Strike Pin isn’t very lining up? Require a chill pill, I am getting there.

Together with your hammer, smack the Lock Box just enough to move that in the direction that needs to visit. In case it won’t move, you screwed that in a bit too tight and even will need to be able to loosen it. If it is arranged properly, you might lock it throughout place to ensure that works. It can be unlocked, associated with course, by keeping the Push Fishing rod (2) through the particular hole in typically the wall until it finally produces. Note that you may have to “fish” around for the smaller hole in the Lock Box to push it in most the way.

Whenever everything is lined up, tighten typically the Lock Box anchoring screws all the approach. If everything is usually well aligned, typically the Push Rod should easily open typically the WG along with the WOHNGEMEINSCHAFT should easily fasten in place. Despite the screws will be tightened, you may possibly be capable of make use of the hammer for final adjustments.

Leave a Reply

Your email address will not be published. Required fields are marked *